How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
We have found the article pertaining to A Step-by-Step Guide to Installing a Bathtub listed below on the web and concluded it made perfect sense to write about it with you over here.
Mounting a tub isn't exactly brain surgery, however it does require strong plumbing, carpentry, and also in some cases, tiling abilities. Replacing an old bath tub with a new one is additionally a moderately difficult job. If the old bathtub is easily accessible, the job can relocate rapidly; if you need to open a wall to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need an assistant to move out the old bathtub and also set in the brand-new one. Make sure you have certified yourself for the task and are comfortable trying it. Rather than employing a service provider to take control of a halfway-completed project, it is far better to consider utilizing one prior to you begin. Opportunities are you may require a professional plumber to make tube connections.
This write-up will aid you install a brand-new bathtub in your shower room if you have actually already gotten a new tub and also don't require to transform the arrangement of your previous water system pipes.
Your tools and also material checklist must comprise the following:
Removing Old Taps
If you need to change old faucets with new ones as a part of your setup, after that the first thing you should do is disconnect the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome as a result of the restricted gain access to that is commonly the instance.
Use a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that attaches the supply pipes to the taps. Have a fabric prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have actually been gotten rid of, make use of the same tool to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this process. When the taps have actually been eliminated, the holes in the bath/basin will certainly need to be cleansed of any kind of old sealing compound.
Before moving on to fit the brand-new faucets, contrast the pipeline connections on the old taps to the new taps. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to stop damages to the string. One end of the adapter fits on the plastic tail of the faucet and also the various other end gives a link to the current supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin guaranteeing that the washers are in place in between the faucet and also the sink. Safeguard the faucet in place with the producer offered backnut. Once the tap is firmly in position, the supply pipelines can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular faucet ports. The former type needs to be attached to the faucet ends first, tightening up just by hand. The supply pipelines can later be connected to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Installing the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the needed position. The wooden boards are practical in uniformly spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto four tiny points.
The following goal is to ensure that the bath tub is leveled all round. This can be achieved by examining the spirit level and changing the feet on the bathtub till the spirit level reviews level.
To install faucets, fit the bottom of the outermost flexible faucet connector to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
Turn on the water as well as examine all joints as well as brand-new pipework for leakages and tighten them if essential. Fill up the bath tub and additionally check the overflow electrical outlet and the typical outlet for leaks.
Ultimately, repair the bathroom paneling as described in the maker's instruction manual. Tiling as well as securing around the tub must wait till the tub has actually been utilized at the very least once as this will certainly settle it right into its final placement.
Preparing for the Installment
Firstly, the sustaining frame provided with the bathroom ought to be fitted (if called for) according to the producer's guidelines. Next, fit the faucets or mixer to the bathtub. When fitting the faucet block, it is essential to see to it that if the tap includes a plastic washing machine, it is fitted between the bathroom and the taps. On a plastic bathroom, it is also practical to fit a sustaining plate under the taps system to stop strain on the tub.
Fit the adaptable tap ports to the bottom of both taps utilizing 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and after that pass the electrical outlet through the hole in the bath. Utilize the nut provided by the manufacturer to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which need to be fitted inside the bath. Ensure you utilize every one of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Attach the bottom of the overflow tube in a similar manner.The bath must currently prepare to be suited its final position.
Tiling Around the Tub
In the area where the bathroom fulfills the floor tile, it is necessary to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to split an inflexible seal, creating the water to penetrate the wall between the bath and the tiling, resulting in issues with moisture as well as feasible leakages to the ceiling listed below.
You can pick from a selection of coloured sealers to assimilate your components and also installations. They are marketed in tubes and also cartridges, as well as are capable of sealing gaps up to a width of 3mm (1/8 inch). If you have a bigger void to fill up, you can fill it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the tub with water before securing, to permit the motion experienced when the tub is in usage. The sealer can split relatively early if you do not take into account this activity prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the marketplace. It is recommended to fit the tiles making use of waterproof or waterproof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I am just very interested in Installing A Bathtub and I really hope you appreciated my piece. So long as you liked our blog posting if you please don't forget to pass it around. We thank you for reading our article about Installing A Bathtub.
Go Services
Report this page